+44 (0)24 7671 8970
More publications     •     Advertise with us     •     Contact us
*/
{megaLeaderboard}
{normalLeaderboard}
News Article

All-CMOS pressure sensor sets new performance standard in wearable and mobile applications

News

ScioSense has introduced the ENS220, an ultra-low power barometric pressure and temperature sensor in a compact package which offers outstanding speed, resolution and accuracy.

The ENS220 is on display at the ScioSense booth B3.419 at Electronica (Munich, 15-18 November 2022).

The sensor’s industry-standard LGA package footprint of 2.0mm x 2.0mm makes the ENS220 suitable for use in wearable and mobile devices such as smart watches and wristbands, GPS navigation systems and personal health monitoring devices.

Altitude or height measurements derived from the ENS220’s relative pressure measurements are accurate to as little as ±2.5 Pa which gives a precision of ±21 cm for a height difference of 83 m. The typical noise level is 0.85 Pa rms at 4ms conversion time.

The combination allows to detect height change as small as 7 cm, which can be used in indoor navigation and localization, activity tracking and fall detection applications.

These applications are enabled by the ENS220’s high speed, low noise and high resolution, as well as its accuracy. Measurements are resolved to 1/64Pa. The output data rate is configurable by the user up to a maximum of 1kHz, enabling device manufacturers to optimize the balance between latency and power consumption. The ENS220’s high accuracy at high speed makes it particularly attractive for applications such as fall detection which require a high-speed series of accurate height measurements in small increments.

This high performance is also compatible with battery power sources thanks to the ENS220’s extremely low power consumption. Operating current at the nominal 1.8V supply voltage is less than 80µA when sampling at 1kHz, just 0.8µA when sampling every minute, and 0.1µA in Idle mode.

All-new all-CMOS architecture

Setting a new standard in the market for small surface-mount pressure sensors, the ENS220 is the result of an important technical innovation. While competing pressure sensors are comprised of a MEMS sensor membrane co-packaged with a CMOS signal-processing ASIC, the ENS220 is different: both the sensor membranes and the ASIC are implemented in CMOS silicon in a single monolithic chip.

This all-CMOS architecture eliminates the parasitics which are generated at the MEMS/CMOS interface in other devices. The all-CMOS architecture also means that ScioSense can match the capacitance of the membranes to the capacitance of the signal-processing circuitry, to minimize noise in circuit elements including the device’s 24-bit ADC. This results in:

A lower noise floor

Higher sensitivity

Smaller size

Lower cost of fabrication

The ENS220’s built-in temperature sensor – accurate to ±0.2K at 8mK resolution – ensures reliable compensation of pressure outputs across the measurement range of 300hPa to 1,200hPa and -40°C to 85°C.

Dirk Enderlein, CEO at ScioSense, said: ‘The ENS220 is the first substantial breakthrough in the pressure sensor market for many years. By implementing the entire sensor in CMOS, ScioSense has dramatically lowered the noise floor, increased sensitivity and shortened conversion time compared to conventional MEMS pressure sensors. This makes the ENS220 the world’s best pressure sensor for applications which require accurate and precise height or altitude measurements at a high sampling rate.’

The ENS220 provides pressure and temperature measurements via digital I2C or SPI interfaces. The device’s LGA package dimensions are 2.0mm x 2.0mm x 0.75mm.

Samples of the ENS220 will be available worldwide from Q1 2023 from authorized distributors. More information may be found at www.sciosense.com

Imec demonstrates co-integration of high-quality SiN waveguide technology with silicon photonics platform
Fraunhofer IPMS presents latest photonic technologies
CEA-Leti Will Highlight Progress on Key Augmented Reality Building Blocks
DigiLens announces partnership with Omnivision
Alif Semiconductor, Bosch Sensortec, and Edge Impulse deliver extended sensor functions
All-CMOS pressure sensor sets new performance standard in wearable and mobile applications
ANELLO Photonics Announce Silicon Photonics Optical Gyroscope
Renesas Will Support Matter on All Future Wi-Fi, BLE and Thread Products
Using sensor technology to protect vulnerable regions
Sony Semiconductor Israel Redefines IoT Connectivity Platform
EnOcean announce agreement with Parabellum Acquisition
Sensor Sales Stay Strong Due to Big ASP Rise
Renesas Unveils First Family of Automotive Radar Transceivers
Melexis has the solution for EV battery current sensing
Sharper Shape enters into agreement to acquire Ai4 Technologies
Infineon introduces new sensor family for automotive applications
Molex Expands North American Manufacturing Capabilities
Imec demonstrates flat-panel-display-compatible pMUT technology
InferSens to Introduce Ultra-Low-Power Edge DL Sensor Technology
Smart sensors for smarter industrial robotics
POLYN Technology Accepted into Silicon Catalyst Incubator Program
Enriching MEMS sensor use cases in CE and IoT
ABB partners with Samotics to expand its condition monitoring services
How LiDAR brings Spatial Intelligence to Airports
Tattile Selects Hailo to Empower its Next-Gen Smart LPR Cameras for ITS
Sivers Photonics receives 1 MUSD follow-up order
Optimized LoRa sensor network power solutions can lower IoT Opex
TERAKI selects Infineon for ML-based radar detection software
MantiSpectra and Vestel cooperate to make home appliances smarter
SICK and Aeva to Bring 4D LiDAR to Industrial Sensing Applications
OMNIVISION Announces World’s Smallest Global Shutter Image Sensor
Flexpoint Receives Significant Interest in OCS System
×
Search the news archive

To close this popup you can press escape or click the close icon.
Logo
×
Logo
×
Register - Step 1

You may choose to subscribe to the Sensor Solutions Magazine, the Sensor Solutions Newsletter, or both. You may also request additional information if required, before submitting your application.


Please subscribe me to:

 

You chose the industry type of "Other"

Please enter the industry that you work in:
Please enter the industry that you work in: